0 голосов
6 просмотров
спросил от Новобранец (58 баллов) в категории Общие вопросы

Lithium-ion Rechargeable Battery Pack
Specification
Product Name: LiFePO4 Li-ion Battery Pack
Product Specification: 3.2V100Ah(26650)
1. Preface
This specification describes the type and size, performance, technical characteristics, warning and caution
of the HETER-3.2V100Ah LiFePO rechargeable pack. The specification only applies to HETER -3.2V100Ah
LiFePO pack supplied by HETER ELECTRONICS GROUP CO.,LTD.
2. Product and Model
2.1 Product: Lithium-ion Battery Pack
2.2 Model: 1IFR3.2-100-Y (26650-3.2V-1S32P)
2.3 Picture And Output Wire (In order to prevail in kind)
Positive outputCopper extremely columnHeight:5mm
Negative outputCopper extremely columnHeight:5mm
3. Battery Pack Specifications
ItemsStandardComments Nominal voltage
Nominal voltage3.2V
Typical capacity100.0±2.0AhAt 0.2C discharge rate
Max continuous discharge
    current100A
Discharge cut-off voltageAbout 2.50V
Charge voltage3.65±0.1VCharge mode: CC/CV,Use a constant
current, constant voltage(CC/CV)
please use special lithium charger.
Charge current≤25A
Inner resistance≤2.0mΩBetween positive and negative polar
Operation temperature
    rangeCharge 0℃~+45℃
Discharge-20℃~+60℃
When the environment temperature is higher than 45℃,please pay attention to
ventilation and heat rejection.
Storage temperature
    range   0℃~40
(Capacity 80%)Recommended long-term storage
temperature is 15~25℃
Humidity5%≤RH≤85%
Shell materialABS
Weight3.50±0.1Kg
Size(L*W*H)(126±1)*(78±1)*(246±1)mm
4.Standard Test Conditions
Battery test must within 1 month after production.
All test in this specification should be in standard atmospheric conditions: temperature:
25± 5℃, relative humidity: 65±20%.
5. Characteristics
5.1 Standard charge
Charge the battery with Lithium ion battery special test cabinet, supply 3.65V voltage, constant-current
0.2C(A) current until current down to 0.02C(A).
5.2 standard discharge
Discharge the battery at 0.2C(A) to 2.50V or battery cut off voltage.
5.3 Electrical Performance
Test ItemsTest MethodsTest Standards
capacity retention
    rateAfter standard charge under 5.1
specified conditions, store the cells for
28 days, then discharge at 0.2C(A )to
cut-off voltage.
Cycle Lifecapacity retention rate≥80%
Cycle Life1) standard charge at 0.2C(A),
2) rest 0.5~1 h
3) discharge at 0.2C to cut off voltage
4) rest 0.5~1h
Cycle Life
capacity retention rate≥80%
repeat the above steps until 1500 cycles.capacity retention rate≥80%
6. Characteristic curve
7. Cautions
7.1Charging current should be less than maximum charge current specified in the Product Specification,
Charging current bigger than recommended current may damage the battery;
7.2Discharging current should be less than maximum discharge current specified in the Product
Specification;Discharging current bigger than recommended current may damage the battery;
7.3 It should be noted that the cell would be possible to be at a over-discharged state by its
self-discharge characteristics in case the cell is not used for long time. In order to prevent
over-discharging, the cell shall be charged periodically to maintain between 3.30V and 3.40V
(2month one cycle),Over-discharging may causes loss of cell performance, characteristics, or
battery functions;
7.4 Please charge the battery within 12 hours after use;
7.5 Battery storage environment follow the above conditions and in standard atmosphere, should be
without strong magnet, no power, no static;
7.6 Do not reverse the polarity of the battery pack for any reason;
7.7 Do not short circuit the battery pack;
7.8 Do not reverse polarity charging;
7.9 Do not immerse the battery pack in water or sea water, or get it wet;
7.10 Do not disassemble battery;
7.11 Do not expose the battery to extreme heat or flame;
7.12 Please use special charger for charging;
8. Product Liability
HETER is not responsible for the incident caused by not obeying the specifications. Before using the battery, you should read the specifications, usage instruction and some attentions carefully to learn its application method and areas. If the phenomenon such as error using method or wrong circuit connection,or input power data, working index are inconsistent with the specifications , cause damage to product, load and its accessories, we are not responsible for it.
Our company have the right to change the content of specification without prior notice;
The final explanation of specification belongs to our company.Battery Module suppliers
website:http://www.jgnebattery.com/battery-module/

Пожалуйста, войдите или зарегистрируйтесь чтобы ответить на этот вопрос.

Похожие вопросы

0 голосов
0 ответов
спросил 2 дней назад от dwp123p Новобранец (54 баллов) в категории Технические вопросы
0 голосов
0 ответов
спросил 2 дней назад от dwp123p Новобранец (54 баллов) в категории Технические вопросы
0 голосов
0 ответов
спросил 20 Ноя от sadsad74 Новобранец (54 баллов) в категории Акции, бонусы
0 голосов
0 ответов
спросил 25 Окт от sp25gg Новобранец (58 баллов) в категории Про читы и макросы
0 голосов
0 ответов
спросил 17 Окт от fhsjnmyh555 Новобранец (54 баллов) в категории Общие вопросы

23.3тыс. вопросов

123тыс. ответов

11.1тыс. комментариев

9.1тыс. пользователей


...